Differences

This shows you the differences between two versions of the page.

--- informatica:arduino:sensores [2016/12/07 18:17] – jose
+++ informatica:arduino:sensores [2016/12/07 18:34] (current) – jose
@@ Line 5: / Line 5: @@
 Conectamos la pata central al Analog0 por ejemplo:
-==== DHT11 ====
+===== DHT11 =====
-Este es digital
+Este es digital:
+http://www.electronicaembajadores.com/Productos/Detalle/37/SSHU004/modulo-sensor-humedad-y-temperatura---conectar-y-listo
 {{:informatica:arduino:sshu04.jpg?200|}}
+Nos tenemos que bajar las bibliotecas (que no librerías) de adafruit de DHT
+https://github.com/adafruit/DHT-sensor-library
+{{ :informatica:arduino:dht-sensor-library-master.zip |}}
+Las descomprimimos en el directorio:
+  /usr/share/arduino/libraries/DHT
+Nos bajamos también las de Adafruit_Sensor y las copiamos en el mismo directorio:
+https://github.com/adafruit/Adafruit_Sensor
+{{ :informatica:arduino:adafruit_sensor-master.zip |}}
+En el código descomentamos DHT11 que es nuestro modelo. Está puesto el pin digital 2: #define DHTPIN 2
+<code>
+// Example testing sketch for various DHT humidity/temperature sensors
+// Written by ladyada, public domain
+#include "DHT.h"
+#define DHTPIN 2     // what digital pin we're connected to
+// Uncomment whatever type you're using!
+#define DHTTYPE DHT11   // DHT 11
+//#define DHTTYPE DHT22   // DHT 22  (AM2302), AM2321
+//#define DHTTYPE DHT21   // DHT 21 (AM2301)
+// Connect pin 1 (on the left) of the sensor to +5V
+// NOTE: If using a board with 3.3V logic like an Arduino Due connect pin 1
+// to 3.3V instead of 5V!
+// Connect pin 2 of the sensor to whatever your DHTPIN is
+// Connect pin 4 (on the right) of the sensor to GROUND
+// Connect a 10K resistor from pin 2 (data) to pin 1 (power) of the sensor
+// Initialize DHT sensor.
+// Note that older versions of this library took an optional third parameter to
+// tweak the timings for faster processors.  This parameter is no longer needed
+// as the current DHT reading algorithm adjusts itself to work on faster procs.
+DHT dht(DHTPIN, DHTTYPE);
+void setup() {
+  Serial.begin(9600);
+  Serial.println("DHTxx test!");
+  dht.begin();
+}
+void loop() {
+  // Wait a few seconds between measurements.
+  delay(2000);
+  // Reading temperature or humidity takes about 250 milliseconds!
+  // Sensor readings may also be up to 2 seconds 'old' (its a very slow sensor)
+  float h = dht.readHumidity();
+  // Read temperature as Celsius (the default)
+  float t = dht.readTemperature();
+  // Read temperature as Fahrenheit (isFahrenheit = true)
+  float f = dht.readTemperature(true);
+  // Check if any reads failed and exit early (to try again).
+  if (isnan(h) || isnan(t) || isnan(f)) {
+    Serial.println("Failed to read from DHT sensor!");
+    return;
+  }
+  // Compute heat index in Fahrenheit (the default)
+  float hif = dht.computeHeatIndex(f, h);
+  // Compute heat index in Celsius (isFahreheit = false)
+  float hic = dht.computeHeatIndex(t, h, false);
+  Serial.print("Humidity: ");
+  Serial.print(h);
+  Serial.print(" %\t");
+  Serial.print("Temperature: ");
+  Serial.print(t);
+  Serial.print(" *C ");
+  Serial.print(f);
+  Serial.print(" *F\t");
+  Serial.print("Heat index: ");
+  Serial.print(hic);
+  Serial.print(" *C ");
+  Serial.print(hif);
+  Serial.println(" *F");
+}
+</code>