Legido Wiki

This page is read only. You can view the source, but not change it. Ask your administrator if you think this is wrong.
====== Temperatura ======
===== TMPM36 =====
{{:informatica:arduino:temperature_tmp36pinout.gif?300|}}

Conectamos la pata central al Analog0 por ejemplo:

===== DHT11 =====
Este es digital:

http://www.electronicaembajadores.com/Productos/Detalle/37/SSHU004/modulo-sensor-humedad-y-temperatura---conectar-y-listo

{{:informatica:arduino:sshu04.jpg?200|}}

Nos tenemos que bajar las bibliotecas (que no librerías) de adafruit de DHT

https://github.com/adafruit/DHT-sensor-library

{{ :informatica:arduino:dht-sensor-library-master.zip |}}

Las descomprimimos en el directorio:
  /usr/share/arduino/libraries/DHT
  
Nos bajamos también las de Adafruit_Sensor y las copiamos en el mismo directorio:

https://github.com/adafruit/Adafruit_Sensor

{{ :informatica:arduino:adafruit_sensor-master.zip |}}

En el código descomentamos DHT11 que es nuestro modelo. Está puesto el pin digital 2: #define DHTPIN 2 


<code>
// Example testing sketch for various DHT humidity/temperature sensors
// Written by ladyada, public domain

#include "DHT.h"

#define DHTPIN 2     // what digital pin we're connected to

// Uncomment whatever type you're using!
#define DHTTYPE DHT11   // DHT 11
//#define DHTTYPE DHT22   // DHT 22  (AM2302), AM2321
//#define DHTTYPE DHT21   // DHT 21 (AM2301)

// Connect pin 1 (on the left) of the sensor to +5V
// NOTE: If using a board with 3.3V logic like an Arduino Due connect pin 1
// to 3.3V instead of 5V!
// Connect pin 2 of the sensor to whatever your DHTPIN is
// Connect pin 4 (on the right) of the sensor to GROUND
// Connect a 10K resistor from pin 2 (data) to pin 1 (power) of the sensor

// Initialize DHT sensor.
// Note that older versions of this library took an optional third parameter to
// tweak the timings for faster processors.  This parameter is no longer needed
// as the current DHT reading algorithm adjusts itself to work on faster procs.
DHT dht(DHTPIN, DHTTYPE);

void setup() {
  Serial.begin(9600);
  Serial.println("DHTxx test!");

  dht.begin();
}

void loop() {
  // Wait a few seconds between measurements.
  delay(2000);

  // Reading temperature or humidity takes about 250 milliseconds!
  // Sensor readings may also be up to 2 seconds 'old' (its a very slow sensor)
  float h = dht.readHumidity();
  // Read temperature as Celsius (the default)
  float t = dht.readTemperature();
  // Read temperature as Fahrenheit (isFahrenheit = true)
  float f = dht.readTemperature(true);

  // Check if any reads failed and exit early (to try again).
  if (isnan(h) || isnan(t) || isnan(f)) {
    Serial.println("Failed to read from DHT sensor!");
    return;
  }

  // Compute heat index in Fahrenheit (the default)
  float hif = dht.computeHeatIndex(f, h);
  // Compute heat index in Celsius (isFahreheit = false)
  float hic = dht.computeHeatIndex(t, h, false);

  Serial.print("Humidity: ");
  Serial.print(h);
  Serial.print(" %\t");
  Serial.print("Temperature: ");
  Serial.print(t);
  Serial.print(" *C ");
  Serial.print(f);
  Serial.print(" *F\t");
  Serial.print("Heat index: ");
  Serial.print(hic);
  Serial.print(" *C ");
  Serial.print(hif);
  Serial.println(" *F");
}
</code>