proxmox:proxmox4
Differences
This shows you the differences between two versions of the page.
| Both sides previous revisionPrevious revisionNext revision | Previous revision | ||
| proxmox:proxmox4 [2016/09/12 11:39] – jose | proxmox:proxmox4 [2019/08/03 19:32] (current) – jose | ||
|---|---|---|---|
| Line 4: | Line 4: | ||
| En resumen, en cada disco creo 3 particiones: | En resumen, en cada disco creo 3 particiones: | ||
| - | 32 Gb / y RAID | + | |
| - | 4 Gb swap | + | 4 Gb swap |
| - | Lo que sobre RAID | + | Lo que sobre para glusterfs |
| - | Y hacemos | + | Y hacemos |
| - | Cuando instalo se queda el segundo RAID (el de datos) así: | + | ====== Configuración |
| - | # cat / | + | Hacemos un bonding y encima un bridge con las dos tarjetas. |
| - | md1 : active (auto-read-only) raid1 sdb3[1] sda3[0] | + | /etc/network/interfaces |
| - | resync=PENDING | + | |
| - | + | ||
| - | Para forzar resync: | + | |
| - | | + | |
| - | Montamos el segundo RAID como datos. Miramos el UUID: | ||
| < | < | ||
| - | # blkid | + | auto lo |
| - | /dev/sda1: UUID=" | + | iface lo inet loopback |
| - | /dev/sda2: UUID=" | + | |
| - | /dev/sda3: UUID=" | + | iface eth0 inet manual |
| - | /dev/sdb1: UUID=" | + | |
| - | /dev/sdb2: UUID=" | + | iface eth1 inet manual |
| - | /dev/sdb3: UUID=" | + | |
| - | /dev/md0: UUID=" | + | auto bond0 |
| - | /dev/md1: UUID=" | + | iface bond0 inet manual |
| + | slaves eth0 eth1 | ||
| + | bond-mode 802.3ad | ||
| + | bond-miimon 100 | ||
| + | |||
| + | auto vmbr0 | ||
| + | iface vmbr0 inet static | ||
| + | address | ||
| + | | ||
| + | | ||
| + | | ||
| + | | ||
| + | bridge_fd 0 | ||
| </ | </ | ||
| - | Añadimos en el fstab: | + | En el switch tenemos que activar port trunk. En mi caso es un tplink tl sg 1024de y entro a la configuración en 192.168.0.1 |
| - | UUID=c3e9ffe8-fb24-405d-abf9-885f201d68c4 | + | |
| + | {{:proxmox: | ||
| + | |||
| + | ===== Configurado red containers ===== | ||
| + | /etc/ | ||
| + | net0: name=eth0, | ||
| + | net1: name=eth1, | ||
| + | |||
| ====== Instalación Proxmox ====== | ====== Instalación Proxmox ====== | ||
| Line 69: | Line 84: | ||
| Desde el primer nodo que será master | Desde el primer nodo que será master | ||
| < | < | ||
| - | root@proxmox01:/gluster# pvecm create clusterproxmox | + | root@proxmox1:~# pvecm create clusterproxmox |
| Corosync Cluster Engine Authentication key generator. | Corosync Cluster Engine Authentication key generator. | ||
| Gathering 1024 bits for key from / | Gathering 1024 bits for key from / | ||
| Writing corosync key to / | Writing corosync key to / | ||
| - | root@proxmox01:/gluster# pvecm status | + | </ |
| + | |||
| + | < | ||
| + | root@proxmox1:~# pvecm status | ||
| Quorum information | Quorum information | ||
| ------------------ | ------------------ | ||
| - | Date: Tue Aug 11 23:23:53 2015 | + | Date: Mon Sep 12 22:37:19 2016 |
| Quorum provider: | Quorum provider: | ||
| Nodes: | Nodes: | ||
| Node ID: 0x00000001 | Node ID: 0x00000001 | ||
| - | Ring ID: 4 | + | Ring ID: |
| Quorate: | Quorate: | ||
| Line 94: | Line 112: | ||
| ---------------------- | ---------------------- | ||
| Nodeid | Nodeid | ||
| - | 0x00000001 | + | 0x00000001 |
| </ | </ | ||
| - | Desde el segundo nodo | + | Desde el segundo nodo lo añadimos poniendo la ip del primero |
| < | < | ||
| - | root@proxmox02:/mnt# pvecm add 192.168.1.4 | + | root@proxmox2:~# pvecm add 192.168.2.1 |
| - | The authenticity of host ' | + | The authenticity of host ' |
| - | ECDSA key fingerprint is 8a:88:8a:2a:d2:8f:96:62:c1:85:ab:fc:c7:23:00:11. | + | ECDSA key fingerprint is 3a:17:aa:ca:c4:1b:55:2a:12:bb:fe:b4:ed:af:1e:af. |
| Are you sure you want to continue connecting (yes/no)? yes | Are you sure you want to continue connecting (yes/no)? yes | ||
| - | root@192.168.1.4's password: | + | root@192.168.2.1's password: |
| copy corosync auth key | copy corosync auth key | ||
| stopping pve-cluster service | stopping pve-cluster service | ||
| Line 111: | Line 129: | ||
| merge known_hosts file | merge known_hosts file | ||
| restart services | restart services | ||
| - | successfully added node 'proxmox02' to cluster. | + | successfully added node 'proxmox2' to cluster. |
| + | </ | ||
| + | |||
| + | Ahora vemos que ya hay dos miembros: | ||
| + | < | ||
| + | root@proxmox1: | ||
| + | Quorum information | ||
| + | ------------------ | ||
| + | Date: Mon Sep 12 22:47:44 2016 | ||
| + | Quorum provider: | ||
| + | Nodes: | ||
| + | Node ID: 0x00000001 | ||
| + | Ring ID: 1/12 | ||
| + | Quorate: | ||
| + | |||
| + | Votequorum information | ||
| + | ---------------------- | ||
| + | Expected votes: | ||
| + | Highest expected: 2 | ||
| + | Total votes: | ||
| + | Quorum: | ||
| + | Flags: | ||
| + | |||
| + | Membership information | ||
| + | ---------------------- | ||
| + | Nodeid | ||
| + | 0x00000001 | ||
| + | 0x00000002 | ||
| </ | </ | ||
| Line 127: | Line 173: | ||
| https:// | https:// | ||
| - | Versión | + | Instalamos versión |
| - | http:// | + | http:// |
| + | |||
| + | Instalamos: | ||
| + | wget -O - http:// | ||
| + | echo deb http:// | ||
| + | apt-get update | ||
| + | apt-get install glusterfs-server | ||
| Queremos montar lo siguiente: | Queremos montar lo siguiente: | ||
| + | |||
| {{: | {{: | ||
| + | En el /etc/hosts añadimos los dos servidores: | ||
| + | < | ||
| + | root@proxmox1: | ||
| + | 127.0.0.1 localhost | ||
| + | 192.168.2.1 proxmox1 | ||
| - | De las dos máquinas | + | 192.168.2.2 |
| - | # gluster peer probe gluster01 | + | </ |
| - | peer probe: success. | + | |
| - | | + | Conectamos los dos servidores. Desde el server1: |
| - | peer probe: success. Probe on localhost not needed | + | root@proxmox1: |
| - | | + | Vemos que están conectados: |
| < | < | ||
| - | root@proxmox01:/mnt# gluster peer status | + | root@proxmox1:~# gluster peer status |
| Number of Peers: 1 | Number of Peers: 1 | ||
| - | Hostname: | + | Hostname: |
| - | Uuid: e95baaf8-8029-4181-89f3-d9e3ebbb9648 | + | Uuid: 62eecf86-2e71-4487-ac5b-9b5f16dc0382 |
| State: Peer in Cluster (Connected) | State: Peer in Cluster (Connected) | ||
| </ | </ | ||
| + | |||
| + | Y desde el server2 igual | ||
| < | < | ||
| - | root@proxmox02:/gluster# gluster peer status | + | root@proxmox2:~# gluster peer status |
| Number of Peers: 1 | Number of Peers: 1 | ||
| - | Hostname: | + | Hostname: |
| - | Uuid: 67d84d45-7551-4b45-b068-8230d1b05cb6 | + | Uuid: 061807e7-75a6-4636-adde-e9fef4cfa3ec |
| State: Peer in Cluster (Connected) | State: Peer in Cluster (Connected) | ||
| </ | </ | ||
| + | Creamos las particiones y formateamos en xfs | ||
| + | < | ||
| - | Creamos el volumen: | + | </code> |
| - | # gluster volume create volumen_gluster replica 2 transport tcp gluster01:/mnt/gluster gluster02:/ | + | |
| - | volume create: volumen_gluster: | + | |
| - | Lo iniciamos: | + | Montamos las particiones en /gluster/brick1 y / |
| - | root@proxmox01: | + | |
| - | volume start: volumen_gluster: | + | |
| - | Miramos el estado: | + | |
| - | | + | |
| + | /dev/sda3: UUID=" | ||
| + | /dev/sdb3: UUID=" | ||
| + | |||
| + | Fichero /etc/fstab | ||
| < | < | ||
| + | #brick 1 | ||
| + | UUID=" | ||
| + | |||
| + | #brick 2 | ||
| + | UUID=" | ||
| + | </ | ||
| + | Creamos el volúmen. Mejor un volumen grande que dos pequeños: | ||
| + | gluster volume create volumen_gluster replica 2 transport tcp proxmox1:/ | ||
| + | volume create: volumen_gluster: | ||
| + | |||
| + | |||
| + | Lo iniciamos: | ||
| + | < | ||
| + | root@proxmox1: | ||
| + | volume start: volumen_gluster1: | ||
| + | </ | ||
| + | |||
| + | Miramos el estado: | ||
| + | < | ||
| Status of volume: volumen_gluster | Status of volume: volumen_gluster | ||
| Gluster process | Gluster process | ||
| ------------------------------------------------------------------------------ | ------------------------------------------------------------------------------ | ||
| - | Brick proxmox01:/gluster/proxmox | + | Brick proxmox1:/bricks/disc1/ |
| - | NFS Server on localhost | + | Brick proxmox2:/ |
| - | Self-heal Daemon on localhost | + | Brick proxmox1:/ |
| + | Brick proxmox2:/ | ||
| + | Self-heal Daemon on localhost | ||
| + | Self-heal Daemon on proxmox2 | ||
| + | |||
| + | Task Status of Volume volumen_gluster | ||
| + | ------------------------------------------------------------------------------ | ||
| + | There are no active volume tasks | ||
| </ | </ | ||
| ===== Conectar como cliente ===== | ===== Conectar como cliente ===== | ||
| - | #mount -t glusterfs | + | #mount -t glusterfs |
| + | | ||
| /etc/fstab | /etc/fstab | ||
| - | | + | |
| | | ||
| - | En un container lxc falla, hay que crear fuse a mano: | + | ====== Almacenamiento compartido Proxmox ====== |
| - | mknod /dev/fuse c 10 229 | + | De momento los containers no soportan GlusterFS directamente desde proxmox, las VMs si. |
| - | + | Montamos /glusterfs y lo ponemos como almacenamiento de Containers (y también de VMs): | |
| - | | + | |
| + | {{: | ||
| - | ====== Almacenamiento compartido Proxmox ====== | ||
| - | | + | {{: |
| + | |||
| + | ====== NFS ====== | ||
| + | Montamos el recurso por nfs en el servidor de proxmox. En los containers los montamos por bind: | ||
| + | |||
| + | En la carpeta / | ||
| + | |||
| + | **Nota:** No poner / delante de container/ | ||
| + | lxc.mount.entry: | ||
| + | **Fuente:** https:// | ||
| + | Ejemplo: | ||
| + | lxc.mount.entry: | ||
| + | lxc.mount.entry: | ||
proxmox/proxmox4.1473680356.txt.gz · Last modified: by jose