This is an old revision of the document!

ARDUINO IDE

Nos descargamos la última versión de Arduino IDE, tiene que ser por encima de la 1.6

Descargamos un plugin para poder conectar con esp32:

https://github.com/espressif/arduino-esp32

https://github.com/espressif/arduino-esp32/blob/master/docs/arduino-ide/boards_manager.md

Ponemos esta URL en file > preferences > Additional Boards Manager URLs:

https://raw.githubusercontent.com/espressif/arduino-esp32/gh-pages/package_esp32_dev_index.json

Ahora vamos a tools > Board: “Arduino Uno” y seleccionamos Boards Manager. Buscamos esp32 y damos a install

En Tools > Board: “Arduino Uno” > ESP32 Arduino

Reiniciamos Arduino. Nos aseguramos que python apunte a python3 instalando python-is-python3

sudo apt install python-is-python3

Código de ejemplo. Conecta a wifi y nos da la ip. Una vez subido tenemos que reiniciar esp32 (desconectando usb)

#include <WiFi.h>        // Include the Wi-Fi library

const char* ssid     = "pitufina";         // The SSID (name) of the Wi-Fi network you want to connect to
const char* password = "reyvisigodo";     // The password of the Wi-Fi network

void setup() {
  Serial.begin(115200);         // Start the Serial communication to send messages to the computer
  delay(10);
  Serial.println('\n');
  
  WiFi.begin(ssid, password);             // Connect to the network
  Serial.print("Connecting to ");
  Serial.print(ssid);

  while (WiFi.status() != WL_CONNECTED) { // Wait for the Wi-Fi to connect
    delay(500);
    Serial.print('.');
  }

  Serial.println('\n');
  Serial.println("Connection established!");  
  Serial.print("IP address:\t");
  Serial.println(WiFi.localIP());         // Send the IP address of the ESP8266 to the computer
}

void loop() { 
  
}

La salida que nos da es esta:

.

Connection established!
IP address:	192.168.1.97

Python

https://www.youtube.com/watch?v=fs10aqFTj8I

apt-get install esptool

Descargamos el firmware:

https://micropython.org/download/esp32/

Descargo este:

 GENERIC : esp32-idf3-20210202-v1.14.bin

Para borrar la memoria. Si no sabemos el puerto, no lo ponemos y lo detecta, es /dev/ttyUSB0:

esptool erase_flash

esptool.py v2.8
Found 1 serial ports
Serial port /dev/ttyUSB0
Connecting........_
Detecting chip type... ESP32
Chip is ESP32D0WDQ6 (revision 1)
Features: WiFi, BT, Dual Core, 240MHz, VRef calibration in efuse, Coding Scheme None
Crystal is 40MHz
MAC: f0:08:d1:d3:1e:98
Enabling default SPI flash mode...
Erasing flash (this may take a while)...

A fatal error occurred: ESP32 ROM does not support function erase_flash.

Da error. Subimos el firmware que hemos descargado. Tarda un poco. Debería devolver un prompt pero no hace nada:

esptool write_flash 0x1000 esp32-idf3-20210202-v1.14.bin

esptool.py v2.8
Found 1 serial ports
Serial port /dev/ttyUSB0
Connecting.......
Detecting chip type... ESP32
Chip is ESP32D0WDQ6 (revision 1)
Features: WiFi, BT, Dual Core, 240MHz, VRef calibration in efuse, Coding Scheme None
Crystal is 40MHz
MAC: f0:08:d1:d3:1e:98
Enabling default SPI flash mode...
Configuring flash size...
Auto-detected Flash size: 4MB
Erasing flash...
Took 2.39s to erase flash block
Wrote 1445888 bytes at 0x00001000 in 140.5 seconds (82.3 kbit/s)...
Hash of data verified.

Leaving...
Hard resetting via RTS pin...

Arduino IDE